- #Icom ic 756 pro ii panadapter install
- #Icom ic 756 pro ii panadapter manual
- #Icom ic 756 pro ii panadapter software
- #Icom ic 756 pro ii panadapter Pc
- #Icom ic 756 pro ii panadapter plus
This makes it possible for the transceiver to be controlled by the waterfall of the SDR program and always display the correct frequency.
#Icom ic 756 pro ii panadapter software
Another program – OmniRig – links the SDR software to the CAT control of the IC-7300. The control software of the SDR is used on a computer, for example HDSDR, SDR-Radio, SDR# or SDR-Uno. With the built-in PTRX-7300 pan adapter, any SDR receiver can now be connected to the new IF output, for example the DXpatrol or a Colibri SDR or others. The installation only takes a few minutes, and a dismantling without residues is possible at any time without problems. The current consumption is only 30 mA, leaving enough power for the external tuner.
The power supply of the buffer amplifier of the PTRX-7300 is provided by the Tuner connector, which is also looped through. The RF signal is picked up and looped through via an existing plug connector on the circuit board here, too, nothing has to be soldered. The additional IF output is mechanically very stable and inconspicuously fixed without having to make any permanent changes to the Icom transceiver. A milled aluminium angle is used instead of the tuner socket of the IC-7300, which is routed to the outside with the supplied cables. The PTRX-7300 board is professionally manufactured and equipped with high-quality components. This ensures that the connected SDR receiver cannot receive any transmit RF. And in the case of transmission, the attenuation is high, typically better than 60 dB. Not so with the PTRX-7300! Due to the careful design of the circuit, the tap of the IF signal is high-impedance and therefore does not load the receiver of the IC-7300 at all, the receive level remains the same. This attenuates the level of the received signal by up to 3 dB. Other solutions to add an RX output to a transceiver simply pick up the signal without worrying about impedance adjustments. All cables needed for the installation are included, the installation is described in detail and with pictures. Nothing is permanently modified on the transceiver, soldering is not necessary.
#Icom ic 756 pro ii panadapter install
And the best thing is: This pan adapter is very easy to install and, if necessary, just as easy to remove. The RX of the 7300 is not affected because the adaptor uses precise impedance matching of the receive signal. The advantage: The Icom’s preamplifier and prefilter are used twice, and the transceiver automatically switches between transmit and receive.
#Icom ic 756 pro ii panadapter Pc
This output allows you to connect a second receiver (SDR) parallel to the IC-7300 and display its spectrum on a large PC screen. The PTRX-7300 extends each IC-7300 by an IF output. So the remote control of the IC-7300 gets a completely new dimension. The PTRX-7300 provides something even better: an IF output to which you can connect any SDR receiver. In the IC-756Pro III, it is possible to program each of the three settings individually with the following preset cutoff frequencies: Lower -6dB point: 100, 300 and 500 Hz., Upper -6dB point: 2.5, 2.7 and 2.9 kHz.A panorama adapter for the IC-7300? What’s the point, you might ask, the IC-7300 has such a nice spectrum and waterfall display? Right, but unfortunately the IC-7300 has no output for an external display. The lower and upper -6dB points of the transmitted audio-frequency response are fixed for each setting. The IC-756 Pro II provided three selectable TOBW settings: WIDE/MID/NAR.
#Icom ic 756 pro ii panadapter manual
Soft and sharp filter shapes can be selected in both SSB and CW modes independently, Programmable SSB transmit bandwidth, microphone equalizer, manual notch function, digital twin pass band tuning (PBT), all mode, including PSK31. 32-bit floating point DSP Digital IF filter with 51 selectable bandwidths. Real-time spectrum scope with mini-scope.
#Icom ic 756 pro ii panadapter plus
121 position microphone equalizer.Ĭovers the nine HF bands and 60-meter plus 6 meters. Soft and sharp filter shapes can be selected in both SSB and CW modes independently, microphone equalizer, manual notch function, digital twin pass band tuning (PBT), all mode, including PSK31. 32-bit floating point DSP Digital IF filter with 41 selectable bandwidths, microphone equalizer, manual notch function, digital twin pass band tuning (PBT), all mode, including PSK31.Ĭovers the nine HF bands plus 6 meters. All successors required no additional filters.Ĭovers the nine HF bands plus 6 meters. 4.9 inch monochromatic TFT dot matrix LCD display.